Last updated on September 1st, 2023 at 10:02 pm
There are a few ways to change the code on your Kwikset Smartcode 909. The first way is to use the Learn button. To do this, press and hold the Learn button until the indicator light comes on.
Then, enter your new 4-8 digit code. The second way is to remove the battery cover and press the Program/Reset button for 20 seconds. This will delete all codes, so be sure to have your new code ready before you begin.
This is the easiest hacks to do so, lets dig deep into the article!
How to Change Code on Kwikset Smartcode 909
If you’re looking to change the code on your Kwikset Smartcode 913, here’s what you’ll need to do:
Things you will need:
- Locate the screws on the interior side of the door that hold the faceplate in place
- Remove these screws with a screwdriver
- Pull the faceplate off of the door to expose the interior workings of the Kwikset Smartcode 909
- Use a Phillips head screwdriver to remove the two screws holding down the control panel. Screwdriver is handy to open deadbolt lock.
- You will need to disconnect any wiring attached to this panel before removing it completely
- Pry open the control panel with a flathead screwdriver to access the circuit board inside
- Find the portion of code you wish to change and use a soldering iron to make your changes
- After making your desired changes, reassemble the control panel and replace it on the door
- Secure it in place with screws and reconnect any wiring that was disconnected earlier
How Do You Change the Code on a Kwikset 909 Front Door Lock?
If you need to change the code on your Kwikset 909 front door lock, it is a relatively easy process.
First, you will need to locate the small hole on the back of the lock. This is where you will insert the reset tool that comes with your lock.
Once the reset tool is in place, turn it clockwise until you hear a click. This indicates that the locking mechanism has been disengaged.
At this point, you can enter in your new code and then turn the reset tool counterclockwise to re-engage the locking mechanism.
Here is the another process to do this using paperclip
First, find the small button on the inside of the door handle. This is the reset button.
Once you’ve found it, use a paperclip or other small object to press and hold it for about 15 seconds.
Next, enter your new code by pressing any four buttons in any order. Be sure to remember this code, as you’ll need it anytime you want to enter your home.
Finally, test out your new code by trying to open the door from the outside. If it opens, then you’ve successfully changed your code!
How to reset Kwikset Smartcode 909 Master Code
The Kwikset Smartcode 909 is a master code-based system that allows you to create and manage codes for up to four users.
This system is designed for use with Kwikset’s Smartcode 914 deadbolt, but can also be used with other products in the Smartcode line.
The 909 provides two methods for creating, managing changing kwikset codes: through the keypad or through the MyKwikset app.
To create or manage codes through the keypad, you will need to enter your master code. Once you have done so, you can add or delete user codes, as well as change the master code itself.
To add a new user code, simply enter the desired four-digit code and press the “Add” button.
You can then assign this code to a specific user by pressing the “User” button and entering the corresponding user number (1-4). To delete a user code, simply press the “Delete” button while on the Add/Delete Code screen.
Finally, to change your master code, press the “Change Master Code” button from any of the three main menu screens.
If you prefer to manage your codes via the MyKwikset app, you will first need to download it and create an account.
Once you have done so, sign in and select your 909 from the list of connected devices. From here, you can add/delete users and change your master code just as you would from the keypad interface.
In addition, you can also set up schedules for when each individual user’s access should be enabled or disabled.
How to Delete All Codes on Kwikset Smartcode 909
If you need to delete all the codes on your Kwikset Smartcode 909, here’s how:
Start with the door open. Press and release the Program button once.
All the lights will flash.
Enter your 4-digit programming code (the default is 1234). The lights will stop flashing.
Press and hold the 6 button until “PC” appears in the display window. Release the button.
Enter 1 2 3 4 5 6 7 8 9 0 # in sequence, then press and release the *button after each number is entered (so a total of 11 presses).
PC should appear in the display again when you’re done entering the numbers. If it doesn’t, start over from step 1.
If you have a SmartKey deadbolt, at this point you’ll need to insert and remove your key from the cylinder twice within 30 seconds to complete step 5b below; if you have a regular deadbolt, skip to step 5b now
Press and hold down both buttons on either side of the display for about five seconds until “SF” appears in the display window; release both buttons
Close and open your door slowly four times within 60 seconds; “CL” should appear in your display window when you’re done
Note: You can apply the method differently for the Kwikset powerbolt 2 reset code.
Can I connect Kwikset lock to my phone?
If you’re looking for a smart lock that you can control with your smartphone, the Kwikset Smartcode 909 APP is a great option. This lock allows you to create up to 30 user codes, so you can give family members and friends their own code to enter your home. You can also monitor who comes and goes using the app’s activity log.
Plus, if you ever lose your phone, you can disable all user codes remotely through the app.
How Do You factory reset Kwikset Smartcode 909?
If you need to Factory reset Kwikset code on your for 909, here’s what you’ll need to do:
1. Start by pressing the “Lock” button on the keypad.
2. Next, enter your 4-digit programming code followed by the “#” sign.
3. Press and release the Schlage button. The LED will blink green to indicate that you’ve successfully entered your code.
4. Finally, press and hold the “Lock” button for 3 seconds.
This will reset the code on your Kwikset SmartCode 909 back to its factory default settings.
How Do You Change the 4 Digit Code on a Kwikset Lock?
If you need to change the 4 digit code on your Kwikset lock, it’s a pretty simple process. Remember this 4 digit code resetting process is applicable for most of the Kwikset smart-keys
Just follow these steps:
Start by pressing the button that is located on the inside of the knob.
You will hear a click sound when you press it.
While continuing to hold down that button, turn the knob to the left until you hear a click. This click signals that you have turned the knob far enough.
Let go of the button and turn the knob to the right until it stops. At this point, your old code is now erased and you can enter in a new 4 digit code.
To test out your new code, simply turn the knob to the left and then back to the right with your new code entered in.
The door should be open if you’ve entered in the correct code!